Skip to content
Grey flake epoxy floor in a commercial building corridor between block walls, gloss finish

Flake floor coatings for businesses

A flake system broadcasts colored vinyl chips into a base coat and seals them under a clear topcoat, giving a textured floor that hides everyday wear.

What a flake floor is

A flake floor is a resin coating, usually epoxy or polyaspartic, with decorative vinyl chips broadcast into the wet base coat. A clear topcoat then locks the chips in place and forms the wearing surface.

The mix of colors breaks up the floor visually, so small scuffs, dust and tire marks are far less noticeable than on a single solid color.

Grey flake epoxy floor with cove base in a restaurant dining area with red chairs

How it is installed

The slab is ground, cleaned and repaired so the base coat bonds evenly. Flake is broadcast by hand across the wet base coat, either as a partial scatter or to full coverage.

Once the base cures, loose chips are scraped and vacuumed off and the clear topcoat goes on. The topcoat can be textured to give more grip in wet areas.

  • Grind, clean and repair
  • Base coat
  • Broadcast flake
  • Scrape and vacuum loose chips
  • Clear topcoat
Light flake epoxy floor in a salon shampoo area with leather shampoo chairs

Key properties

Flake floors add texture and depth, which helps footing and hides imperfections in the slab. The clear topcoat carries the chemical and abrasion resistance, so the choice of topcoat matters as much as the flake color.

Full-broadcast systems build more thickness than a plain coating, which adds durability in areas with carts and rolling equipment.

Grey flake epoxy floor with a cove base beside a restaurant counter

Where flake floors are used

Flake is popular wherever a floor needs to look finished but take real use: staff areas, restrooms, service counters and customer-facing work bays.

Grey flake floor with a cove base in a room with a bay window

Strengths, limits and when to choose something else

Flake hides wear, adds grip and gives a finished look at a moderate cost. It is not designed for hot washdown or steam, where urethane cement holds up better.

Where a floor needs to look sleek and polished rather than textured, metallic epoxy or polished concrete are better fits. For very heavy commercial wear in wet areas, a quartz broadcast is often chosen instead.

Grey flake floor in a large, bright garage with a cove base and high windows

Care and maintenance

  • Sweep or dust mop regularly and clean with a neutral cleaner and a soft-bristle brush or auto-scrubber.

  • A textured topcoat holds a little more dirt, so a deck brush helps in heavily used spots.

  • If the topcoat wears thin in traffic lanes, a new clear coat can be added before the flake layer is exposed.

At a glance

PropertyWhat to expect
LookMulti-color chips under a clear topcoat
WearHides scuffs, dust and minor marks
FootingTextured; can be tuned for wet areas
DowntimeShort to moderate, depending on resins used
LimitsNot for hot washdown or steam
UpkeepNeutral cleaner, soft brush, recoat clear layer

FAQ

Flake coatings: questions

Straight answers to the questions we hear most.

Light grey flake garage floor with sunlight across it

Are flake floors slippery when wet?

The chips add texture, and the clear topcoat can include grit for extra grip. How much texture to add depends on the space; a restroom and an office lobby usually get different finishes.

What is the difference between partial and full flake?

Partial flake scatters chips over a solid base color so some of the base shows through. Full broadcast covers the base completely, adds thickness and usually hides more wear.

Can a flake floor run up the wall as a cove base?

Yes. An integral cove carries the coating a short way up the wall, which removes the seam where dirt and water collect. It is common in restrooms, kitchens and clinics.

Is flake the same as quartz?

No. Flake uses vinyl chips for color and pattern, while quartz uses colored sand that builds a harder, more textured surface. Quartz is often chosen for heavier wet-area use.

Ready for a bid?

Send the details or plans for a written bid.

Request a Bid
Squeegee spreading freshly poured grey coating over a prepared hangar slab

Request a bid

Ready for a bid?

Send your project details or plans. We reply within 1 business day.