

Commercial floor coating questions, answered
What owners, facility managers and contractors ask most often about scheduling, prep, systems, safety, insurance and how a bid comes together.
Scheduling & downtime
Can you install while we stay open?
Usually, yes. We work nights, weekends and in sections (after-hours work is priced accordingly), following our return-to-service schedule.
How long until we can use the floor?
It depends on the system, the temperature and the traffic the floor has to carry. Floors return to service in stages: foot traffic first, then rolling loads and vehicles.
Can you work during our planned shutdown?
Yes. Shutdowns and holiday weekends are when most plant floors get coated; we plan crews and curing around the window you have.
Can you phase by zone?
Yes. Phasing is how most occupied warehouses get coated: we agree the zones and the order with you.
Can you coat around racking?
Yes. We work zone by zone, coating open aisles and the floor under racking that can be cleared; your scope shows each zone's dates.
Can you do one bay at a time?
Yes, bay-by-bay is common so the shop stays open.
Can you schedule several locations at once?
Yes. We can plan the order with you, store by store.
Prep & testing
Do you test the concrete first?
Yes, when the slab needs it, and the testing is listed in the bid. Slab moisture is a leading cause of coating failure; if it is high, we quote a mitigation primer instead of gambling with your floor.
Our building is new. When can the slab be coated?
After it passes a moisture test. A new slab can take weeks to dry enough; we test it when it needs it, list that in the bid and tell you, rather than coat it early, so the coating isn't the first thing to fail.
Why do industrial floor coatings fail?
The most common causes are poor surface prep, moisture coming through the slab, and a system that does not match the chemicals or traffic it sees. Getting those three right prevents most failures.
Why does the concrete have to be ground before coating?
Grinding removes the weak top layer, old sealers and contaminants and opens the surface so the coating can bond into it. A coating rolled onto smooth or dirty concrete has little to grip and is more likely to peel.
Can a new floor go over existing quarry tile?
Sometimes, if the tile is fully bonded and sound, but loose or cracked tile has to come out first. In many kitchens removing the tile gives a more reliable result and avoids raising the floor height at drains.
What happens to plumbing and electrical trenches in the slab?
Trenches are usually filled with concrete or repair mortar and then ground flush with the surrounding slab. Some finishes, especially polished concrete, may still show the patch, so the finish choice should account for it.
Why do joints need to be refilled over time?
Concrete slabs keep shrinking slightly for some time after they are poured, which can open joints and pull filler away from the edges. Checking and topping up joint fill keeps the edges protected.
Systems & durability
Which products do you use?
There's no standard product per system: every commercial job is spec'd to the site. The system and product are chosen for your slab, your traffic and what lands on the floor.
What is the difference between a sealer and a coating?
A sealer soaks into or sits thinly on the concrete to reduce dust and staining, while a coating builds a thicker protective layer on top. Coatings usually resist wear and chemicals better, and sealers cost less for large, light-use areas.
Can it take steam cleaning?
Yes — that's what urethane cement is for. It handles steam cleaning, hot washdown and thermal shock.
Will it resist our solvents and acids?
Tell us what's on the floor and we'll match a system with the manufacturer's chart to prove it.
Can different areas of a plant use different systems?
Yes, it is common to use one system in general production and another in wet, hot or chemical-heavy areas. Matching each zone to its conditions usually performs better than one system everywhere.
Why do some garage coatings peel under car tires?
Peeling usually comes from a thin coating, poor surface prep or a product that softens with heat. When a coating is not bonded into a properly profiled slab, a hot tire can grip it and pull it up as it cools.
Can a coating handle heavy pallet racking?
Coatings are commonly installed under racking, but rack base plates concentrate a lot of weight on a small spot. Some projects coat before racking goes in, while others coat the aisles around existing racks.
Does road salt damage a coated floor?
Salt and the slush that carries it are hard on bare concrete, but a sealed coating keeps the salt water on the surface. Regular rinsing and cleaning keeps the salt from building up and dulling the finish.
Can a coating hide an old, stained slab?
Opaque coatings, metallic epoxy and flake systems cover stains and patches well. Polished concrete and stains show the slab's character, so they suit floors with fewer blemishes.
Safety & compliance
Are your floors slip-resistant?
We build texture into the system to suit each area. We don't promise a slip-resistance number unless the manufacturer's data backs that exact system.
Can we see the slip texture before you coat?
Texture is built in to suit each area, and you can pick your color from real samples.
Is there such a thing as USDA-approved flooring?
No. No agency approves or certifies a floor, so 'USDA-approved flooring' isn't a real thing; we build to the Food Code's surface requirements.
Will this pass an audit?
Neither the FDA nor USDA FSIS approves a floor. The floor supports your compliance — seamless, cleanable, nonabsorbent — but an audit covers the whole facility, not just the floor.
Is it OSHA compliant?
OSHA sets requirements for keeping floors clean, dry where feasible, and free of hazards; it doesn't certify coatings. A seamless, textured floor that's easy to clean makes meeting those requirements easier.
What is a cove base and why does it matter?
A cove base is the coating carried up the wall in a smooth curve instead of meeting it at a sharp corner. That curve is easy to clean and keeps water and debris from collecting where the floor and wall meet.
Is polished concrete slippery?
Polished concrete is usually no more slippery than other smooth hard floors when it is clean and dry. Spills and dust make any smooth floor slicker, so mats at entrances and prompt cleanup matter.
Do you do safety striping and line marking?
Yes. We stripe aisle lines, pedestrian walkways and hazard zones, laid out with you, with a new coating or on an existing floor.
Do you install ESD (static-control) floors?
Yes. An ESD floor is a premium system, priced above standard coatings.
Insurance
Are you licensed and insured?
Yes. Elevated Coatings is licensed and insured, and a certificate of insurance is available on request.
Can you send a certificate of insurance before we sign?
Yes. Ask for a certificate of insurance with your bid request, or through the contractors page, and we send a current copy.
What should we keep after the floor is finished?
Keep the written bid with your building records; it names the system that was installed.
The bidding process
What do you need from us to start a bid?
Send the building type, size and timing, and any plans or photos. Most bids include a site visit, where we look at the slab, test it and agree the work window; some are bid from plans or an RFQ.
What's included in the written bid?
The scope, in writing: the system, the prep and the areas covered.
What does it cost per square foot?
It depends on the slab's condition, the system, the size and the schedule, so each floor is priced in writing, usually after a site visit (some bids are priced from plans or an RFQ).
Can you work to a fixed budget?
Yes. Give us the number up front and we can scope a system to fit it, or tell you if the space needs more.
Do we need a general contractor to hire you?
No. Many owners hire us for the floor themselves; if you have a contractor, we schedule around them.
Is the price the same for every location?
We can bid each store on its own slab and size, to the same spec; prep can differ from store to store.
What areas do you serve?
All of Utah, from our shop in West Valley City, and Idaho for larger projects.

Request a bid
Ready for a bid?
Send your project details or plans. We reply within 1 business day.